Your Trusted Partner in Electronics Supply Chain. Inquire Now!

Explore Our Latest Smart Electronics Collection.

20491l1-124-klixon-thermal-protector, 20491l1-124-klixon-thermal-protector, /circuit-protection
Inquiry
Inquiry

20491L1-124 Klixon Thermal Protector

Request a Quote
  • Overview

Overview

Request 20491L1-124 when your approved equipment record calls for this specific Klixon device. The photos show the marked housing, screw terminals and metal mounting plate. Use those views to check identity and physical layout before asking for a quote. Condition on request. The images do not establish a switching temperature, contact arrangement or suitability for a particular appliance.

Compare the mounting plate against the equipment

The metal plate is a useful first reference because it shows how the body sits relative to the visible mounting features. Put the approved drawing or a reference unit beside the gallery when comparing the Klixon thermal protector. Record where the plate must sit in the assembly and which features need to align. If a cover or neighboring component restricts access, include the available clearance in the review. Do not estimate hole spacing or body depth from a photograph without a verified scale.

Keep the plate check separate from the thermal interface. Even a similar mounting arrangement does not prove that the device will respond as required in your equipment. Ask the responsible reviewer which surfaces and orientation matter to the approved assembly. If the drawings leave a question open, request a sample for an identification or fit review rather than accepting a visually similar replacement for installation. Record the purpose of the sample and the evidence needed to close that question.

Use the screw terminal view to clarify the quote

Look at the terminal side of the screw terminal thermal protector to compare visible fasteners, position and access. The photo does not specify torque, terminal assignments or conductor requirements. Use the equipment manufacturer's approved instructions for those details. If your existing unit retains external hardware after removal, identify which pieces belong to the equipment rather than assuming the quoted component includes them. Ask for a clear view of the actual offered unit when a fastener or terminal position is an acceptance requirement.

Record the mounting view and terminal view together in the order file. That makes it possible to distinguish a discrepancy caused by a different viewing angle from a physically different unit. Where a supplier proposes another screw terminal thermal protector, request a separate line with the full part number and supporting evidence. Do not allow the alternate to replace the original quote line until someone responsible for the application has approved it.

Preserve the complete marking in the service record

Write 20491L1-124 on the quote request and the receiving checklist. Keep the final 124 and the characters before it intact. A family name or search alias may help find an old record, but it should not replace the approved part number. If the original unit cannot be read, consult the equipment bill of materials or ask for a better image. Document where the confirmed identifier came from rather than silently filling in missing characters.

A Klixon thermal protector should be reviewed against the approved application before it is installed. Contact action, calibration and reset behavior are separate from the visible housing. If a technical specification is needed, ask for the documentation that applies to the exact reference. Do not infer a setting from another model or decode the marking into a temperature without verified documentation. Keep unresolved technical questions on the quote or receiving record until the responsible reviewer resolves them.

Build a usable request for quotation

  • Give 20491L1-124 as the manufacturer reference and indicate whether alternate numbers may be listed separately.
  • Identify the equipment and drawing revision, and describe any mounting plate or terminal layout that must match the approved screw terminal thermal protector.
  • Specify the sample and order quantities, destination, target receipt date and any required inspection evidence.
  • Ask for the condition, offered quantity and packing in the response. Request the actual unit marking if it is needed for approval.

At receipt, compare the offered Klixon thermal protector with the accepted quote and approved reference before issuing it to maintenance. Note whether the check was based on an original part, a drawing or a photograph. If the plate or terminal view differs, hold the unit and ask the buyer to resolve the difference. A visual identity check is not an electrical test. Use the approved acceptance procedure for any evaluation that goes beyond the visible features.

Document the acceptance decision

For a repeat service purchase, retain a photo of the accepted marking and the equipment drawing reference in the receiving record. Note which mounting details were visible and which were checked separately against the drawing. If a supplier later offers parts from different packing, request the identity evidence required by the purchase order rather than assuming the previous comparison still applies. Assign a reviewer for any discrepancy, and do not release an unidentified part into the approved spare bin. A short record of the decision is more useful on the next order than a generic description copied into inventory.

Questions for a maintenance buyer

Can I match this part by the plate and screws alone?

No. Those features help identify the screw terminal thermal protector, but the approved part number and equipment documentation govern the replacement decision.

Can I request an alternative while the exact match is being quoted?

Yes. Ask for a separate part number and quote line. The equipment owner should compare the differences before accepting a substitute.

Does the photo confirm condition or how many are available?

No. Ask for the condition and quantity actually offered for the Klixon thermal protector. The photo is an identification aid, not an inventory statement.

Use Request a Quote for 20491L1-124. Send the requested quantity and destination, and identify the mounting, marking or inspection details that should accompany the quote.

20491L1-124 Klixon Thermal Protector

Request a Quote
{"cf_related_products":{"field_type":"product","type":"array","value":[],"config":""}}

Related Products

Explore premium ICs, sensors, and power controls to support your advanced technical requirements.

20491l1 124 klixon thermal protector-2

Get a Free Quote

Our representative will contact you soon.
Email
WhatsApp / Mobile Phone
Company Name
Part Number
Message
0/1000
Attachment
Please upload at least an attachment (Optional)
Upload up to 5 files (maximum 30 MB). Supported formats: JPG, JPEG, PNG, PDF, DOC, DOCX, XLS, XLSX, CSV, TXT, STP, STEP, IGS, X_T, DXF, PRT, SLDPRT, SAT, RAR, ZIP.