Your Trusted Partner in Electronics Supply Chain. Inquire Now!

Explore Our Latest Smart Electronics Collection.

35hm509-47-klixon-motor-protector, 35hm509-47-klixon-motor-protector, /circuit-protection
Inquiry
Inquiry

35HM509-47 Klixon Motor Protector

Request a Quote
  • Overview

Overview

Use the -47 variant as the starting point

35HM509-47 is the reference shown on the photographed Klixon unit and its corresponding Sensata carton. The part photo shows the marked body and leads through a sleeve. Request this exact reference when a controlled motor assembly calls for it, rather than specifying only the 35HM family. The electrical calibration, lead arrangement and packing are separate questions, so the quotation should identify what is known about each one.

Keep the electrical review with the equipment owner

Sensata describes the 35HM family as an on winding protector family for three phase motors. That does not give the exact setting or fit of this Klixon 35HM motor protector. For a compressor or motor repair, ask the equipment owner for the approved parts reference, applicable drawing revision and any protective characteristic needed for acceptance. Do not substitute a family temperature range, a current taken from a similar motor, or a value copied from another 35HM suffix.

The useful question for an engineer is whether the offered unit matches the assembly in the approved record. Ask them to review the requirement for the winding interface and terminal configuration as well as the required behavior. Do not infer reset characteristics for 35HM509-47 from the carton or the shape of the housing. If the exact part information is unavailable, mark the request as an identification enquiry or an evaluation sample. A request to buy a sample is not authorization to install it.

Turn the lead and sleeve requirements into quote fields

For a motor protector with leads, ask for a clear view of the offered lead ends and describe the dimensions or termination details the buyer needs to verify. The pictured sleeve helps show the presentation of the photographed unit, but it does not establish the dimensions or material of every offered piece. If sleeve condition or configuration is an acceptance item, request confirmation in writing. The supplier can then distinguish a question about packaging from a requirement that affects the approved assembly.

Use a short comparison record for a Klixon 35HM motor protector: complete number, approved assembly reference, visible lead configuration, and any open questions. Save a photo that shows the relationship between the leads and housing rather than separate crops that are difficult to associate. If the lead arrangement on the offered sample differs, ask the reviewer whether it is a different variant, a documented acceptable alternative or an unresolved mismatch. Do not edit the ordering number to make the difference disappear.

Keep purchasing and receiving records consistent

Enter 35HM509-47 as the manufacturer part number in the enquiry and retain the final 47 on the order. If the supplier proposes another motor protector with leads, require a separate quote line and its complete part number. Keep the comparison evidence with the equipment record so the receiving team knows which configuration was accepted. This is especially useful if several 35HM parts are stored together or if repair teams at different sites use different internal stock references.

The carton image is evidence of the label that was photographed. It does not establish the number available now, whether the offered shipment will be in that carton, or the current condition of all units. If lot separation, packing or a particular inspection document matters, agree on it before placing the order. At receipt, compare the agreed reference with the physical unit label and lead layout. Set a mismatched item aside for the responsible buyer and engineering reviewer rather than accepting it under a shortened family code.

Include these details in the request

  1. Give the exact Klixon 35HM motor protector reference and indicate whether alternatives are allowed on separate lines.
  2. Identify the approved motor or equipment assembly and the drawing or parts record used to identify the spare.
  3. For a motor protector with leads, state which lead, termination or sleeve details need confirmation and whether an inspection sample is required.
  4. Separate sample and order quantities. Include the destination, target receipt date and any requirements for packing, condition or traceability.

Before committing to a full lot, define the difference between a visual identity check and an acceptance test. An inspection can confirm that the body marking and physical features match the agreed reference. It cannot establish electrical suitability without the appropriate documentation and qualification. If one department requests a replacement and another receives the material, give both teams the same acceptance checklist. Record which questions were resolved on the quote and which still belong to the engineering review.

Specify how an inspection sample will be identified

If the purchase is being qualified with a sample, give the sample its own order line and identify how it will be tied to the subsequent offered lot. Ask whether the supplier can provide a photograph of the label and lead ends before shipment. Record which features the sample review is meant to settle. If the balance will come from a different lot or arrive in different packing, request a new identity check where your procedures require one. A sample may answer a fit question without answering which condition or packing will apply to the balance.

Questions for buyers comparing 35HM options

Can a part with another 35HM ending be treated as an exact replacement?

No. Ask for the full offered number and verify the application separately. A similar shell does not confirm the approved configuration of a Klixon 35HM motor protector.

Does the pictured sleeve specify the complete lead assembly?

No. Use the photo to discuss the offered motor protector with leads, then ask for the exact details required by the approved drawing or inspection plan.

What if only the carton is marked clearly?

Ask for the offered device marking and relevant photographs. Keep the carton reference as supporting evidence, not as the sole proof of identity or condition.

Use Request a Quote for 35HM509-47. Send the quantity and delivery destination, and state which lead details and lot evidence need to appear in the quotation.

35HM509-47 Klixon Motor Protector

Request a Quote
{"cf_related_products":{"field_type":"product","type":"array","value":[],"config":""}}

Related Products

Explore premium ICs, sensors, and power controls to support your advanced technical requirements.

35hm509 47 klixon motor protector-2

Get a Free Quote

Our representative will contact you soon.
Email
WhatsApp / Mobile Phone
Company Name
Part Number
Message
0/1000
Attachment
Please upload at least an attachment (Optional)
Upload up to 5 files (maximum 30 MB). Supported formats: JPG, JPEG, PNG, PDF, DOC, DOCX, XLS, XLSX, CSV, TXT, STP, STEP, IGS, X_T, DXF, PRT, SLDPRT, SAT, RAR, ZIP.